Print this page

Erlo TF Serie Milling and Drilling Machine with Electromagnetic Automatic Feed

Milling and drilling machine with electromagnetic automatic feed, geared drive and a cross table. Drilling capacity: 35 mm (1 3/8"). Milling capacity: 55 cm3/min.

Drilling Milling Machine with Electromagnetic Automatic Feed

  • Feed electromagnetic automatic
  • Feed: 0,10-0,18-0,24
  • Transmission gears
  • Column diameter: mm
  • Distance from spindle to column: 390 mm
  • Drilling capacity: ⌀ 35 mm
  • Milling capacity: 55 cm3/min
  • Spindle cone: CM 4
  • Engine power: 1.2 | 2 HP
  • Num. and selections of speeds: (16) 94 - 2225 rpm
  • Drilling depth: 180 mm
  • Fixed base and moveable bit
  • Coordinates table: 360 x 1220 mm
  • Motorised bit movement
  • 45º tiltable bit on each side
  • Front wheel for sensitive fine feed
  • Manual grease pump, for guides, column and table
  • Tool holding clamp
  • Weight: 910 kg
  • Measurements: 1510 x 1660 x 2600 mm
  • Bench with door and drawer
  • Cooling equipment: (SR)
  • Light equipment

Standard Equipment

  • Motorized headstock displacement
  • Prismatic column
  • Guides, Column and table manual greasing pump
  • Depth adjustable end
  • Frontal wheel for fine sensitive feed
  • Coolant equipment
  • Tool spanning system
  • Lighting equipment
  • Main switch
  • Emergency push button
  • Turning sense selector
  • Electrical equipment at low voltage
  • Command plate installed in articulated arm
  • Drill guard with stop micro
  • CE norms

Optional Equipment

  • Depth digital reading
  • Reversing for tapping IR/RS
  • Tapping system by lead screw with braking device (1 spindle included)
  • Additional lead screw special pitch
  • Additional lead screw standard pitch
  • Automatic longitudinal displacement by motorised feed box
  • Automatic transversal displacement by motorised feed box
  • 1 axis digital viewer (in control plate over articulated arm)
  • 2 axis digital viewer (in control plate over articulated arm)
  • 3 axis digital viewer (in control plate over articulated arm)
  • Collet chucks, set of collets, key, box and locking nut
  • Column supplement 250 mm.
  • Supplement by ISO.30 taper
  • Supplement by ISO.40 taper
  • Automatic tool fastening for ISO taper
  • Column prolongation
  • Emel pneumatic synchronised cycle
  • Integral drilling cycle for tubes/ profiles and intermittences
  • Bi manual command

Technical Specifications

MODEL TF.35
DRILLING CAPACITY IN STEEL OF 70 Kg. 35 mm
TAPPING CAPACITY IN STEEL OF 70 Kg. M35
MILLING CAPACITY (mm) 55
TRANSMISSION GEARS (Hardened and grounded)
NUMBER AND RANGE OF SPEEDS (RPM.) 50 Hz. (16) 94 - 2225 rpm
FEED AUTOMATIC
NUMBER AND RANGE OF FEEDS (3) 0,10-0,18-0,24
CLUTCH ELECTROMAGNETIC
MAIN MOTOR POWER 1,2/2 HP
MAIN MOTOR SPEED (rpm.) 750/1500 rpm
SPINDLE CONE MT4
SPINDLE STROKE 180
DISTANCE SPINDLE-COLUMN 390
DISTANCE SPINDLE-TABLE Min. 190 / Max. 650
DIMENSIONS OF THE CROSS TABLE 360x1220 mm
MANUAL CROSS TABLE STROKE (STANDARD) X=700 / Y=360
MOTORIZED CROSS TABLE STROKE (EXTRA OPTIONAL EQUIPMENT) X=650 / Y=350
TABLE WITH "T" SLOTS SI
TILTING TABLE 45º TO EACH SIDE
WEIGHT: NET/GROSS Kg. 910 / 1400 KG.
PACKAGING DIMENSIONS AND VOLUME 1680 x 1680 x 2520 mm / 7,11 m3
Montfort International
2500 av. Watt, Quebec City (Qc),
G1P 3T3, Canada
1-800-463-6668
info@montfort-international.com